How to Reset - Remove - Bypass a BIOS or CMOS Password without using any software

DISCLAIMER: This information is intended for experienced users. It is not Intended for basic users, hackers, or computer thieves. Please do not try any Of following procedures if you are not familiar with computer hardware. We'll Not be responsible for the use or misuse of this information, including Personal injury, loss of data or hardware damage. So use it at your own risk.

BIOS passwords are used to add some extra security to computers. You can either Set a password to prevent access to BIOS settings or to prevent PC from booting.But sometimes this extra security might become a pain when you forget the BIOS Password or someone changes your system BIOS password intentionally.But there is no need to worry. There are many known ways to reset / remove / Bypass the password:

a) By removing the CMOS battery
b :) By using the motherboard jumper
c :)  By using MS DOS command
d :) By using Backdoor BIOS password

A.By Removing the CMOS Battery:
Almost all motherboards use a small coin sized CMOS battery to store all BIOS Settings along with the password. To reset the password, unplug the PC, open the Cabinet and remove the CMOS battery for approx. 15-30 minutes and then put it Back. It'll reset all BIOS settings as well as the password and you'll need to Re-enter all settings.If it fails, then try to remove the battery for at least one hour.

B.By Using the Motherboard Jumper:
 Almost all motherboards contain a jumper that can clear all CMOS settings along With the BIOS password. The location of this jumper varies depending upon the Motherboard brand. You should read your motherboard manual to check its Location. If you don't have the manual then look for the jumpers near the CMOS Battery. Most of the manufacturers label the jumper as CLR, CLEAR, CLEAR CMOS, Etc.When you find the jumper, look carefully.  There will be 3 pins and the jumper Will be joining the center pin to either left or right pin. What you need to do, Is removing the jumper and join the center pin to the opposite pin. E.g. if the jumper joins center pin to left pin, then remove it and join center pin to right Pin. Now wait for a few seconds and then again remove the jumper and join the Center pin to left pin.Make sure to turn the PC off before opening the cabinet and resetting the
Jumper.

C.By Using MS DOS Command:
This method works only if you have access to the system when it’s turned on Because this method requires MS DOS. Open Command Prompt from Programs menu and Provide following commands one bye one:
  debug
  o 70 2E
  o 71 FF
  quit


NOTE: The first character in the above commands is "O" and not the number 0.After providing the above commands, restart your system and it should reset the CMOS Settings along with the BIOS password.
If you are curious to know how it works? Then let me explain the above commands: In this method we are using the Debug tool of MS DOS. The "O" character present  At first in these commands, outputs the values to IO ports. The number 70 and 71 Are port numbers which are used to access CMOS memory. By providing FF value we are telling CMOS that there is an invalid checksum and it resets the CMOS
Settings as well as BIOS password.

D.By Using Backdoor BIOS Password:

Some BIOS manufacturer put a backdoor password in BIOS which always works
Irrespective of what password you have set in BIOS. It’s a master password which
Is used for testing and troubleshooting purposes.

AMI BIOS Passwords:
  A.M.I.
  AAAMMMIII
  AMI?SW
  AMI_SW
  AMI
  BIOS
  CONDO
  HEWITT RAND
  LKWPETER
  MI
  Oder
  PASSWORD
AWARD BIOS Passwords:
  01322222
  589589
  589721
  595595
  598598
  ALFAROME
  ALLy
  aLLy
  aLLY
  ALLY
  aPAf
  _award
  award
  AWARD_SW
  AWARD?SW
  AWARD SW
  AWARD PW
  AWKWARD
  awkward
  BIOSTAR
  CONCAT
  CONDO
  Condo
  d8on
  djonet
  HLT
  J64
  J256
  J262
  j332
  j322
  KDD
  Lkwpeter
  LKWPETER
  PINT
  pint
  SER
  SKY_FOX
  SYXZ
  syxz
  shift + syxz
  TTPTHA
  ZAAADA
  ZBAAACA
  ZJAAADC
PHOENIX BIOS Passwords:
  BIOS
  CMOS
  phoenix
  PHOENIX
Misc Common Passwords:
  ALFAROME
  BIOSTAR
  biostar
  biosstar
  CMOS
  cmos
  LKWPETER
  lkwpeter
  setup
  SETUP
  Syxz
  Wodj
Other Manufacturer BIOS Passwords:
  Biostar - Biostar
  Compaq - Compaq
  Dell - Dell
  Enox - xo11nE
  Epox - central
  Freetech - Posterie
  IWill - iwill
  Jetway - spooml
  Packard Bell - bell9
  QDI - QDI
  Siemens - SKY_FOX
  TMC - BIGO
  Toshiba - Toshiba
  VOBIS &  IBM - merlin

NOTE: All these passwords are case-sensitive and are changed from time to time by manufacturers.`

Read More

How to Install Ubuntu with Windows 8 without using the Virtual Machine.

Here, We describe How can we install the Ubuntu (GUI version of Linux OS) with Windows Eight Operating System. Ubuntu will be install with Windows 8 without the Virtual Machine in Windows drive.

To install Ubuntu with Windows we need two files. one is Windows-based Ubuntu Installer (WUBI) and another one is Ubuntu OS ISO file. You can download those file from the below link.

Windows-based Ubuntu Installer:  http://www.ubuntu.com/download/desktop/windows-installer
Ubuntu ISO file:                               http://www.ubuntu.com/download/desktop
Note: WUBI is different for each version of Ubuntu. So always try to download the latest version or the same version of WUBI and the ISO file of Ubuntu OS.

Process:

1. Download the above two files and put it in a single folder in your Windows 8.
2. Open WUBI as administrator and click on OK on the UAC prompt screen.
3. You will get 5 options on the Open “Ubuntu Installer” application window. Select the options as per your requirement and availability.
  Installation Drive: Choose the drive where you want to install the Ubuntu.
  Installation Size: Allocate the memory for the Ubuntu on the installation Drive (Minimum 5GB)
  Desktop Environment: Choose Ubuntu
  Language: Choose your preferred language on which you want to install Ubuntu.
  User Name: add a user name for Ubuntu (By default it is same windows username but you can also change it)
  Password: Set a password for Ubuntu User.
4. Click on “Install“. Complete the installation Process by following the Instruction.
5. It will ask to reboot or Manually reboot later. Just Reboot your system.
6. After reboot you will get two options on your Boot Screen. Choose “Ubuntu“.
7. Follow the instruction and Complete the last step of your Ubuntu Installation.
That is it. Now you will able to use Two operating System (Windows 8 and Ubuntu) on your system.

Note: Ubuntu will automatically install a sound card, Graphic, Ethernet driver. But before the execution of any application Ubuntu needs to be updated. So install the required Update.

Read More

HOW TO OPEN/OPEN BLOCKED SITES

In many schools, collges, institutions, offices they will block mainly social network sites

Reasons of not opening website
1.The website itself blocking you
2.The website is blocked blocked by someone or instituton

To recover from this problems

problem 1
 Due to bad ip this problem will occurs . It automatically recover from server

problem 2

just open www.hidemyass.com or  www.kproxy.com or www.flyproxy.com any one these websites and
type your required url provided by above websites in search box

Enjoy the unblocked websites using this trick

Thank you for visting

Read More

How To Increase The Speed of All Torrents Downloads without any software

Sometimes we face lots of download problem from a torrent software. Some of the problem are
1. We are not able to download more than 8 files simultaneously.
2. our download speed is very slow.
Problem 1:
     We are not able to download more files simultaneously.
This is due to the some of the default setting of your software. There is already a limited value is assigned for maximum number of active downloads/uploads and also for maximum number of active torrents.Maximum number of active torrents refers the number of torrent download/upload files you have added.Maximum number of active downloads refers to the number of download you are simultaneously using.
here is the process to change these values.
steps:
   1. Run the Bit torrent software.
   2. Now click on "setting"
   3. Now select the "Queueing"
   4. Now on the right hand side you will find the "Queue Setting"
   5. Now change the value for Maximum number of active torrents and Maximum number of actve downloads as many as you like there is no restriction for this.





Problem 2:
    Our torrent download speed is slower than other down loader.
For a high speed download our internet provider should provide a high speed internet. But within a limit speed we face problem that torrent download speed is slower than other downloader. This is due to during download simultaneously upload process is started. And I personally feel that upload speed very badly affect the download speed. And by default upload and download has average band width speed is maximum i.e. infinity.
So for downloading at a higher rate we have to stop the upload. We can not stop the entire upload but we can reduce the average band width upload speed. For this follow these

Steps:
  1. Start a torrent download by double clicking the torrent file. (A torrent file is a file which has .torrent extension)
  2. Now right click the active download torrent.
  3. Select the "band width allocation".
  4. Now select "set upload limit" and change the value to minimum i.e. 1 kb/s
  5. By default you will not find the minimum value 1 kb/s. You will find a value more than this.
  6. There you select the minimum value which is present there.
  7. Now again repeat the 2nd, 3rd and 4th step.
  8. At last you will be able to selct the minimum value for upload speed.
  9. Be sure to select download speed to maximum. (after step 3 select set upload limit)

Read More

Latest Winrar full version with key free download | How to make Evalution copy of Win-rar registered

                          


The process will show you how to make an Evaluation Copy of Win-Rar registered full version using the Crack. The crack is able to make any version of Win-Rar registered. The Evaluation Copy of Win-Rar works for 60 days after that it works but show an Error Message to activate.

Installation Process of Win-Rar Crack

1. Download and Install any version (latest) of Win-Rar.
2. Download the patch  or Crack from the below download link and Extract it to your desktop using any of RAR Archiever.
3. Open Run Window and type "%appdata%" and click on "Ok".
4. it will open "C:\Users\[Your Use Name]\AppData\Roaming".
5. Open "Winrar" folder there.
5. Copy all the downloaded file and paste them on that Win-Rar Folder.
6. Now reboot your system and After reboot you will find that your Evaluation Copy of Win Rar is now Full Version.That is it.
   
DOWNLOAD LINK CLICK HERE

Read More

Latest Turbo C++ for Windows XP Vista 7 32 bit free download

What is turbo C++
Turbo C++ is a C and C++ language compiler is an Integrated Development Environment (IDE) originally developed by Borland. An integrated development environment (IDE) is a software application that provides comprehensive facilities to computer programmers for software development. An IDE normally consists of a source code editor, build automation tools and a debugger

Installation Process for Turbo C++ latest version

This version of Turbo C++ supports only 32 bit and 16 bit version of Windows. It doesn't supports 64 bit Operating System. It will work good and in full screen Mode in Windows XP. it does not support full screen mode in Windows Vista and Windows 7 with 32 bit(x86).

1. Download the RAR file given below
2. Extract it using WinZip or Winrar or any other archiever and you will get the Turbo C++ installation files.
3. Right Click on the file and choose "Run as Administrator".
4. Click on "OK" if the UAC prompt if appears.
5. Then Click on "Install'. It will install the turbo C++ on c:\tc.
6. If you want to change the Installation directory then click on "Browse" and choose your Installation directory for Turbo C++ and then click on "Install".
7. It will install the applications and a shortcut will be created on desktop.
8. Just Click on that shortcut to open Turbo C++.

DOWNLOAD LINK

Read More

BlackBerry Z10 Full Phone Specifications and Features

I may think BlackBerry is something like Apple who use all its own product for its Smartphone? Because of its own OS BlackBerry 10 for its Z10 or Not because of 1.5GHz Qualcomm S4 Plus Processor which is not its own product like Apple’s 1.2GHz Apple A6. In front view both Apple iPhone 5 and [...]

Hide/Show Phone Detail
Phone Name: BlackBerry Z10
2G Network: GSM 850 / 900 / 1800 / 1900 - all versions
3G Network: HSDPA 850 / 900 / 1900 / 2100 - STL100-1; HSDPA 850 / 900 / 2100 - STL100-2
4G Network: LTE 800 / 900 / 1800 / 2600 - STL100-2
SIM: Micro-SIM
Dimensions: 130 x 65.6 x 9 mm (5.12 x 2.58 x 0.35 in)
Weight: 137.5 g (4.83 oz)
Display Type: Capacitive touchscreen, 16M colors
Display Size: 768 x 1280 pixels, 4.2 inches (~355 ppi pixel density)
Display Multitouch: Yes
Display Protection: N/A
Call Alert Type: Vibration, MP3 ringtones
Loudspeaker: Yes
3.5mm Jack: Yes
Memory Card Slot: microSD, up to 64 GB
Memory Internal: 16 GB storage, 2 GB RAM
GPRS: Yes
EDGE: Yes
Data Speed: HSDPA 21 Mbps, HSUPA 5.76 Mbps; LTE, EV-DO Rev. A, up to 3.1 Mbps
WLAN: Wi-Fi 802.11 a/b/g/n, dual band
Bluetooth: Yes, v4.0 with A2DP, LE
USB: Yes, microUSB v2.0
NFC: Yes
Primary Camera: 8 MP, 3264 x 2448 pixels, autofocus, LED flash
Camera Features: Geo-tagging, face detection, image stabilization
Camera Video: Yes, 1080p@30fps, video stabilization
Camera Secondary: Yes, 2 MP, 720p@30fps
OS: BlackBerry 10 OS
Chipset: Qualcomm MSM8960 Snapdragon
CPU: Dual-core 1.5 GHz Krait
GPU: Adreno 225
Sensors: Accelerometer, gyro, proximity, compass
Messaging: SMS, MMS, Email, Push Email, IM, BBM 6
Browser: HTML5
Radio: No
GPS: Yes, with A-GPS support
Java: Yes, MIDP 2.1
Colors: Black, White
Other Features: SNS integration; HDMI port; BlackBerry maps; Organizer; Document viewer; Photo viewer; MP3/WMA/WAV/eAAC+/FlAC player; DivX/XviD/MP4/WMV/H.263/H.264 player; Voice memo/dial; Predictive text input
Battery: Li-Ion 1800 mAh battery
Battery Stand By: Up to 312 h
Battery Talktime: Up to 10 h
I may think BlackBerry is something like Apple who use all its own product for its Smartphone? Because of its own OS BlackBerry 10 for its Z10 or Not because of 1.5GHz Qualcomm S4 Plus Processor which is not its own product like Apple’s 1.2GHz Apple A6. In front view both Apple iPhone 5 and BlackBerry Z10 look like similar but other high-end Smartphone are very giant in look than iPhone 5, Lumia 920.

As per hardware and software specifications and features it is not that impressive because its specs very much similar to all other devices. Only Speciality in BlackBerry Z10 is that its own BlackBerry 10 latest OS.

Read More